CCTV Telemetry Receivers  (140)

Interface reciever, compatible with fixed speed and variable speed domes. Designed to operate over 1km using CC125 cable. Video Output - 1V p-p to 4V p-p 75R impedance via BNC socket. Power required - 9 - 12V AC/DC Functions - dependent on model of dome.

The RF3227E RF Receiver allows the option bus of compatible control panels to receive RF signals from up to 96 wireless devices. The RF3227E supports up to eight keypads and 96 key fobs or input sensors. Tamper, jam detection, and sensor missing status reports provide reassurance that the system works correctly. The RF3227E receives at 433.42 MHz.

Ernitec BDR-512/2 telemetry receiver features 2 auxiliary relays. It receives and presents commands to PTZ, motorised lenses and auxiliary equipment. Fitted with power supplies and housed in IP-rated, weather proof boxes, it is available with video transmitters for twisted pair cable and power Supply for 230 VAC pan/tilt. 64 telemetry receivers can be connected on a single line up to 1200 meters apart.

The LTC 4744 Transmitter and LTC 4745 Receiver are designed for the transmission of up to 4 CCTV analog video signals using one multimode fiber cable. This link operates in the 1310 nm range and incorporates 8-bit video encoding exceeding the requirements of EIA RS-250C for Medium Haul video transmissions. Integral LED status indicators provide an indication of operating parameters.

Each model allows Bosch I/P bus control panels to receive RF signals from wireless devices. The wireless devices save time for busy installers and homeowners and the receivers are a valuable option for system users who want additional security without disruptive installations. Tamper, jam detection, and sensor missing status reports confirm that the system is working properly.

The 1-2-1 converter is designed to provide single address  protocol conversion. The 1-2-1 converter accepts RS485/422 data from one source, converts it to one of a wide range of possible RS485/422 protocols.

The RX10X is designed to offer a simple solution for applications where there is a need to control a variety of 3rd Party Dome Camers.

BBV RX400PWBX telemetry receiver features coax or twisted pair cabling with Integral Video Launch AMP, pan tilt zoom focus iris lights wash/wipe autopan presets in IP65 box.

Controlled from either BBV Up-the-Coax over 250M of RG59 or 500M of CT125 or BBV 20mA current loop, each will control a single dome from a switch-selectable range of protocols.

Ernitec BDR-550/2 is a twisted pair telemetry receiver providing: Text insertion and the opportunity to programme up to 30 seperate pre-positions for PTZ. Sequences of any 30 of the pre-positions are programable. A service keyboard is included to facilitate testing during installation. It features 255 units on one twisted pair line as well as 6 auxiliary relay output.

Ernitec BDR-511/2 is a twisted pair telemetry receiver with 2 auxiliary relays. It receives and presents commands to PTZ, motorised lenses and auxiliary equipment and is fitted with power supplies and housed in IP-rated, weather proof boxes, available with video transmitters for twisted pair cable and Power Supply for 24 VAC pan/tilt. 64 telemetry receivers can be connected on a single line up to 1200 meters apart.

6 auxiliary relays.  Receives and presents commands over a twisted pair cable.  64 telemetry receivers can be connected on a single line up to 1200 meters apart.  In the event of local power failure the station is by-passed, allowing communication to the other units.

Advanced features include fully-scaleable dynamic privacy zones, mimic patrols, 3-D dynamic text, configurable auxiliary relays and advanced motor control setup. Alarm management facilities which include camera power fail and anti-tamper can be handled locally by the ZVR-530, reported to the local site or reported to a remote site permitting multiple automatic responses to be actioned.

To meet the increasing demand for ‘privacy zones' in public area CCTV systems, Ernitec BDR580 incorporates dynamic electronic zone masking that enables the privacy of those in  adjacent areas, not under surveillance, to be maintained.  The size and shape of the zone  masks are automatically adjusted to compensate for camera and zoom angle in order to maintain privacy, whilst maximising the view of the rest of the scene.  The privacy zones can be quickly programmed via an easy-to-follow, on-screen menu.  Not only can you create a zone as big or a small as you like but you can also choose the degree of opacity of that zone, varying it where necessary to maintain security.

RX10X/WBX is compatible with both fixed speed and proportionally controlled variable speed domes.

RX10X/AL is a controlled from either BBV Up-the-Coax over 250M of RG59 or 500M of CT125 or BBV 20mA current loop, each will control a single dome from a switch-selectable range of protocols.

The LTC 8561 Series, LTC 8564/20, and LTC 8566 Series on-site receiver/drivers are control data decoder units and motor drivers for pan/tilt units and zoom lenses. These receiver/drivers are used in conjunction with Allegiant® Series Microprocessor-based Switcher/Controller Systems.

Additonal 16 camera input card for the TX1500 series, for up to 96 cameras.  Systems larger than 96 cameras use multiple cards.  Camera range must be specified at time of order, and is now available in a MK1 and MK2 version, please see the datasheet for which version to order.

2 auxiliary relays.  Receives and presents commands to PTZ, motorised lenses and auxiliary equipment.  Fitted with power supplies and housed in IP-rated, weather proof boxes, available with video transmitters for twisted pair cable and Power Supply for 24 VAC pan/tilt.  64 telemetry receivers can be connected on a single line up to 1200 meters apart.

Advanced Telemetry Receivers which share the features of Series BDR-510, while providing: Text insertion and the opportunity to programme up to 30 seperate pre-positions for PTZ.  Sequences of any 30 of the pre-positions are programable.  A service keyboard is included to facilitate testing during installation.  255 units on one twisted pair line. 6 auxiliary relay output.

Coax or Tw.Pair cabling, Integral Video Launch AMP, pan tilt zoom focus iris wash/wipe lights PCB only, in IP65 box.

Coax or Tw.Pair cabling, Integral Video Launch AMP, pan tilt zoom focus iris lights wash/wipe autopan presets, in IP65 box.Suitable for controlling dc high & variable speed heads.

Coax, AC type, 24 V AC, 4 functions, 0, RX, 280 x 190 x 130, 0.6 kg, -10~+40

The D-TECTX Receiver - is an IP 55 weatherproof, tamper protected, four channel unit equipped with two volt free & two negative switched outputs. It can be expanded by the addition of 3 further four channel expansion modules to allow the Receiver unit to monitor the active state of up to 16 wireless D-TECTX Movement Detectors.

Video Output - 1V p-p to 4V p-p 75R impedance via BNC socket. Power required - 240V 50Hz, or 110 volts 60 Hz optional. Functions - 9.

Additonal 16 camera input card for the TX1500 series, for up to 96 cameras.  Systems larger than 96 cameras use multiple cards.  Camera range must be specified at time of order, and is now available in a MK1 and MK2 version, please see the datasheet for which version to order.

Designed primarily for external fixed cameras requiring wash and wipe facilities the ZVR-130+ incorporates a host of other advanced features including camera captions, alarm inputs, camera fail detection and remote camera configuration. The On Screen Display (OSD) facilities allow user configuration of a 14-character caption along with alarm and camera status information.

The CTI Coax Interfaces are a range of innovative products designed to provide conversion from RS422/485 data to BBV up the coax.

The Vigitron Vi6100DR is an active device that receives colour or B&W video and data over separate point-to-point unshielded twisted pair wires at distances up to 6000 feet (1830 m).  It is designed to be paired with Vigitron Vi6100DT active video and data transmitter.

The RX200 offers control of ac driven pan only or wash / wipe / lights for static cameras.

The MIC Series USB to RS485 signal converter is a compact unit that allows a PC without a serial port to connect directly to the MIC Series cameras via the telemetry connector in MIC Series power supplies. The converter is connected in 4-wire two-way mode (Full Duplex); in 2-wire two-way mode (Half Duplex) or in 2- wire one-way mode (Simplex).

Input signal is duplicated onto eight outputs.  Accepts RS-232, RS-422 and RS-485 simplex serial signals. Outputs up to eight balanced serial signals.  Transmission distance up to 5 km.  Multiple units can be cascaded for more than eight outputs. Galvanic separation between input and outputs.  Power failure indication.  Mains power selectable between 115 and 230 VAC.

Battery backed up RAM on each DRL2E line card module.  Up to 8 different handshakes per profile.  Low battery detection and automatic low battery disconnect.  Telephone line supervision and reporting.  Caller ID, calling name and DNIS.  Communicates in all major ITI formats, all common pulse formats, 4/1, 4/2, 4/3 and DTMF format, FBI Super Fast format, RADIONICS Modem II, Modem IIE, Modem IIa, BFSK formats, SK FSK1, FSK2 formats.

DSC DRL2E twisted pair telemetry receiver features 2 digital lines, DSP processing.  It expands MLR2-E to 30 lines. The receiver also features flash memory, Caller ID, two-way voice recording. It can be programmed from the CPM2 or PC with console software.

The CTI Coax Interfaces are a range of innovative products designed to provide conversion from RS422/485 data to BBV up the coax.

Additonal 16 camera input card for the TX1500 series, for up to 96 cameras.  Systems larger than 96 cameras use multiple cards.  Camera range must be specified at time of order, and is now available in a MK1 and MK2 version, please see the datasheet for which version to order.

Bosch LTC 878060 Data Converter Unit is designed for various applications utilising Allegiant Series Switchers. It converts Allegiant Bi-Phase control code to RS-232 and RS-232 to Bi-Phase and provides satellite address decoding. The signal distribution mode provides 15 separate outputs.

Bosch LTC 856160 is a full-featured pan/tilt/zoom/aux control with auto-pan/random pan, Bi-Phase or RS-232 data input, 99 pre-positions with tour capability, pre-positions compatible with 360° continuous pan/tilt drives, and integral local test feature.

The LTC 8562 Series on-site receiver/drivers are control data decoder units and motor drivers for pan/tilt units and zoom lenses. These receiver/drivers are used in conjunction with Allegiant Series or microprocessor based switcher/controller systems.

LTC 8560 series single-channel on-site receiver/drivers.  PTZ control.  Bi-phase or RS-232 data input.  Compatible with Allegiant Systems.  Integral local test feature.  Indoor/outdoor applications.