CCTV Power supplies & batteries  (637)

A power supply with 4 x 1Amp 24V AC fused outputs. Ideal for powering 24V AC CCTV cameras and camera housing heaters. Metal cased.

A power supply with 2 x 2Amp 24V AC fused outputs. Ideal for powering 24V AC CCTV cameras and camera housing heaters.

A power supply with 8 x 1Amp 24V AC fused outputs. Ideal for powering 24V AC CCTV cameras and camera housing heaters.

A power supply that provides 2 x 2A 12V DC outputs. Each output is fused and is provided with internal LED indication, the PSU also accepts a wide mains input range. The unit is intended for use with CCTV cameras. Metal cased.

A power supply that provides 4 x 1A 12V DC outputs. Each output is fused and is provided with internal LED indication, the PSU also accepts a wide mains input range. The unit is intended for use with CCTV cameras. Metal cased.

4 Amp output, hinged box.

1 Amp output, multiple indicators, hinged box.

Power supply unit with a single regulated 12V DC 1A output. The unit’s mains and output leads are wire ended to allow easy connection to terminal blocks etc. ABS, wall-mountable, case.

ReServ2WP Outdoor Video Surveillance UPS is designed to provide power for 24 V AC cameras during normal or power outage conditions. True sine wave regulated AC outputs.

An In-Line power supply that provides a single regulated 12V DC 500mA output. The unit’s mains and output leads are wire ended to allow easy connection to terminal blocks etc. ABS, wall-mountable, case.

Altronix DPS5 power supply/charger converts a low voltage AC input into a 6VDC, 12VDC or 24VDC output. This unit has a wide range of applications for access control, security and CCTV system accessories that require additional power.

Altronix DPS1 power supply/charger converts a low voltage AC input into 6VDC, 12VDC or 24VDC output. This general purpose power supply has a wide range of applications for access control, security, and CCTV system accessories that require additional power.

Connectivity to the X-SERIES camera and control equipment is made via pluggable terminal blocks. Video cable has option of terminal block or BNC connection. Weatherproof enclosure to IP 66 comes complete with range of cable glands ready fitted.

Sixteen (16) power LEDs. Illuminated master power disconnect circuit breaker with manual reset. 3-wire grounded line cord. Removable terminal blocks with locking screw flange.

60 W power supply Constant Voltage design for external LED lighting applications Built-in active Power Factor Correction (PFC), typically > 0.93 Turn on time < 1 second with soft start Protection: Over-Load, Over Current, Open Circuit, Short Circuit, Over Temperature

Provides all connections for power, telemetry and video for the MIC series range of PTZ cameras. Weather-resistant, cast-aluminum IP65 enclosure. Weather-resistant 1/2-in. NPT, M16, and M12 cableglands for connection of power, video, telemetry and ancillary equipment. Integrated header for addition of ancillary cards such as the MIC alarm card, washer pump drive card or biphase converter card (non IR power supplies only). Ground isolation and termination to control videogrounding and to prevent ground loops.

Illuminated power disconnect circuit breaker with manual reset. Removable terminal blocks w/locking screw flange. IEC 320 - 3-wire grounded line cord (detachable). 3U rack mount chassis for use in standard EIA 19" rack. Ease of installation saves time and eliminates costly labor.

Illuminated power disconnect circuit breaker with manual reset. Removable terminal blocks w/locking screw flange. IEC 320 - 3-wire grounded line cord (detachable). 3U rack mount chassis for use in standard EIA 19" rack. Ease of installation saves time and eliminates costly labor.

The Bosch UPA Series of Power Supplies is designed specifically for the continual use demands of professional surveillance products. While UPA models are used primarily with security cameras, their small size and high energy efficiency rating also make them ideal for powering a wide range of other low power security products, including many Allegiant® system accessories and control devices.

Provides all connections for power, telemetry and video for the MIC series range of PTZ cameras. Weather-resistant, cast-aluminum IP65 enclosure. Weather-resistant 1/2-in. NPT, M16, and M12 cableglands for connection of power, video, telemetry and ancillary equipment. Integrated washer pump drive with test function (IR power supplies only). Integrated four-input alarm terminal (IR power supplies only). Ground isolation and termination to control videogrounding and to prevent ground loops.

Provides all connections for power, telemetry and video for the MIC series range of PTZ cameras. Weather-resistant, cast-aluminum IP65 enclosure. Weather-resistant 1/2-in. NPT, M16, and M12 cableglands for connection of power, video, telemetry and ancillary equipment. Integrated header for addition of ancillary cards such as the MIC alarm card, washer pump drive card or biphase converter card (non IR power supplies only). Ground isolation and termination to control videogrounding and to prevent ground loops.

Altronix eFlow104NB UL Listed Sub-Assembly power supply/charger converts a 120VAC, 60Hz input into a single 24VDC output. It also offers a suite of features that includes fire alarm disconnect, overvoltage protection, and low power disconnect which prevents deep discharge of stand-by batteries.

100 W power supply Constant Voltage design for external LED lighting applications Built-in active Power Factor Correction (PFC), typically > 0.93 Turn on time < 1 second with soft start Protection: Over-Load, Over Current, Open Circuit, Short Circuit, Over Temperature

Bosch UPA-2410-60 power supply unit is designed specifically for the continual use demands of professional surveillance products. While the unit is used primarily with security cameras, its small size and high energy efficiency rating also make it ideal for powering a wide range of other low power security products, including many Allegiant® system accessories and control devices.

Bosch UPA-12300-60 power supply unit is designed specifically for the continual use demands of professional surveillance products. While the unit is used primarily with security cameras, its small size and high energy efficiency rating also make it ideal for powering a wide range of other low power security products, including many Allegiant® system accessories and control devices.

Bosch UPA-2430-60 power supply unit is designed specifically for the continual use demands of professional surveillance products. While the unit is used primarily with security cameras, its small size and high energy efficiency rating also make it ideal for powering a wide range of other low power security products, including many Allegiant® system accessories and control devices.

35 W power supply Constant Voltage design for external LED lighting applications Built-in active Power Factor Correction (PFC), typically > 0.93 Turn on time < 1 second with soft start Protection: Over-Load, Over Current, Open Circuit, Short Circuit, Over Temperature

Bosch MIC-IP-PS-115 is a 115 VAC IP-enabled power supply unit for MIC Series cameras. It ensures that the cameras can be installed in a variety of locations, including low voltage and mobile applications. It conforms to the National Transportation Communications for ITS Protocol (NTCIP) specification. NTCIP conformance ensures that the power supply unit integrates with transportation management devices. It has UL, CE, and FCC approval, is rated to IP67 as well as supports 50/60 Hz.

50 VA, UL/CSA approved.

Provides all connections for power, telemetry and video for the MIC series range of PTZ cameras. Weather-resistant, cast-aluminum IP65 enclosure. Weather-resistant 1/2-in. NPT, M16, and M12 cableglands for connection of power, video, telemetry and ancillary equipment. Integrated header for addition of ancillary cards such as the MIC alarm card, washer pump drive card or biphase converter card (non IR power supplies only). Ground isolation and termination to control videogrounding and to prevent ground loops.

Altronix ALTV1224C4 AC/DC Dual Output Power Supply is designed to provide both 12VDC and 24VAC outputs where a combination of both AC and DC outputs is required. It provides two (2) 12VDC outputs with a total current of 2A and two (2) 24VAC outputs with a total current of 4A.

MobileView MVA-BATT-12-10-B1 is a UPS battery with type 1 MTG bracket.

50 VA, UL/CSA approved.

UPA power supplies provide efficient, constant power for CCD and MegaPixel cameras, keyboards and other low power usage products.  Meet or exceed International Energy Efficiency Level IV requirements.  Screw terminals for ease of installation on some models. 

Sixteen (16) power LEDs. Illuminated master power disconnect circuit breaker with manual reset. 3-wire grounded line cord. Removable terminal blocks with locking screw flange. Spare fuses provided.

Sixteen (16) power LEDs. Illuminated master power disconnect circuit breaker with manual reset. 3-wire grounded line cord. Removable terminal blocks with locking screw flange. Spare fuses provided.

Altronix eFlow104NKA8QM converts a 120VAC 60Hz input into eight (8) fuse protected outputs. Outputs are individually selectable, providing 12VDC or 5VDC up to 6A and/or 24VDC up to 10A (240W total power) for access control panels, door locks, and ancillary devices. Power outputs can be converted to dry form “C” contacts. Outputs are activated by an open collector sink, normally open (NO), normally closed (NC) dry trigger input, or wet output from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. eFlow104NKA8QM will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs. The spade connectors allow you to daisy chain power to multiple LINQ8ACM modules. This feature allows you to distribute the power over more outputs for larger systems. Built-in LINQTM Network Power Management facilitates monitoring, reporting and control of power/diagnostics.

Altronix eFlow104NKA8D converts a 120VAC 60Hz input into eight (8) PTC protected powerlimited outputs. Outputs are individually selectable, providing providing 12VDC or 5VDC up to 6A and/or 24VDC up to 10A (240W total power) for access control panels, door locks, and ancillary devices. Power outputs can be converted to dry form “C” contacts. Outputs are activated by an open collector sink, normally open (NO), normally closed (NC) dry trigger input, or wet output from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. eFlow104NKA8D will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs. The spade connectors allow you to daisy chain power to multiple ACMS8CB modules. This feature allows you to distribute the power over more outputs for larger systems.

Altronix eFlow104NKA8 converts a 120VAC 60Hz input into eight (8) fuse protected outputs. Outputs are individually selectable, providing 12VDC or 5VDC up to 6A and/or 24VDC up to 10A (240W total power) for access control panels, door locks, and ancillary devices. Power outputs can be converted to dry form “C” contacts. Outputs are activated by an open collector sink, normally open (NO), normally closed (NC) dry trigger input, or wet output from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. eFlow104NKA8 will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs. The spade connectors allow you to daisy chain power to multiple ACMS8 modules. This feature allows you to distribute the power over more outputs for larger systems.

PSU2SM from Genie has an integral mounting lug and has long power leads, 1.8 metres each.  It is for indoor use only.