CCTV Power supplies & batteries  (637)

Provides all connections for power, telemetry and video for the MIC series range of PTZ cameras. Weather-resistant, cast-aluminum IP65 enclosure. Weather-resistant 1/2-in. NPT, M16, and M12 cableglands for connection of power, video, telemetry and ancillary equipment. Integrated washer pump drive with test function (IR power supplies only). Integrated four-input alarm terminal (IR power supplies only). Ground isolation and termination to control videogrounding and to prevent ground loops.

Altronix ALTV1224C Series AC/DC dual output power supplies provide both 24VAC and 12VDC outputs where a combination of both AC and DC outputs is required. They provide eight (8) 12VDC outputs at 3.5A total max. and eight (8) 24VAC outputs at 3.5A total max.

Sixteen (16) power LEDs. Illuminated master power disconnect circuit breaker with manual reset. 3-wire grounded line cord. Removable terminal blocks with locking screw flange. Spare fuses provided.

Sixteen (16) power LEDs. Illuminated master power disconnect circuit breaker with manual reset. 3-wire grounded line cord. Removable terminal blocks with locking screw flange.

Sixteen (16) power LEDs. Illuminated master power disconnect circuit breaker with manual reset. 3-wire grounded line cord. Removable terminal blocks with locking screw flange. Spare fuses provided.

Illuminated master power disconnect circuit breaker with manual reset. 3-wire grounded line cord. Removable terminal blocks with locking screw flange. Unit maintains camera synchronization. Spare fuses provided.

Altronix eFlow104NKA8DQM converts a 120VAC 60Hz input into eight (8) PTC protected power-limited outputs. Outputs are individually selectable, providing 12VDC or 5VDC up to 6A and/or 24VDC up to 10A (240W total power) for access control panels, door locks, and ancillary devices. Power outputs can be converted to dry form “C” contacts. Outputs are activated by an open collector sink, normally open (NO), normally closed (NC) dry trigger input, or wet output from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. eFlow104NKA8DQM will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs. The spade connectors allow you to daisy chain power to multiple LINQ8ACM modules. This feature allows you to distribute the power over more outputs for larger systems. Built-in LINQTM Network Power Management facilitates monitoring, reporting and control of power/diagnostics.

Power supply for 9 camera. 4 Amp (100VA) supply current. Integral surge protection. Underwrites laboratory recognised. Individual LED power indication and individual PTC output protection.

Power supply for 16 camera. 8 Amp (200VA) supply current. Integral surge protection. Underwrites laboratory recognised. Individual LED power indication and individual PTC output protection.

Altronix ALTV164 CCTV Power Supply is designed to power CCTV cameras and accessories. It provides 16VAC @ 6A or 18VAC @ 5A supply current, distributed via four (4) fuse protected outputs.

Altronix ALTV1224C4220 AC/DC Dual Output Power Supply is designed to provide both 12VDC and 24VAC outputs where a combination of both AC and DC outputs is required. It provides two (2) 12VDC outputs with a total current of 2A and two (2) 24VAC outputs with a total current of 4A.

Altronix ALTV1224C220 Series AC/DC dual output power supplies provide both 24VAC and 12VDC outputs where a combination of both AC and DC outputs is required. They provide eight (8) 12VDC outputs at 3.5A total max. and eight (8) 24VAC outputs at 3.5A total max.

Sixteen (16) power LEDs. Illuminated master power disconnect circuit breaker with manual reset. 3-wire grounded line cord. Removable terminal blocks with locking screw flange.

Sixteen (16) power LEDs. Illuminated master power disconnect circuit breaker with manual reset. 3-wire grounded line cord. Removable terminal blocks with locking screw flange. Spare fuses provided.

Illuminated master power disconnect circuit breaker with manual reset. 3-wire grounded line cord. Removable terminal blocks with locking screw flange. Unit maintains camera synchronization. Spare fuses provided.

Altronix eFlow102N is a power supply/charger that converts a 120VAC 60Hz input into a single 12VDC output with a total of 10A max. The unit includes a unswitched aux. output. It also offers a suite of features that includes fire alarm disconnect, over voltage protection, and low power disconnect which prevents deep discharge of stand-by batteries.

eFlow104N is a power supply/charger that converts a 120VAC 60Hz input into a single 24VDC output with a total of 10A max. The unit includes an unswitched aux. output. It also offers a suite of features that includes fire alarm disconnect, over voltage protection, and low power disconnect which prevents deep discharge of stand-by batteries.

Altronix eFlow102NXV is a power supply/charger that converts a 220VAC (working range 198VAC - 256VAC), 50/60Hz input into a single 12VDC output with a total of 10A max. The unit includes an unswitched aux. output. It also offers a suite of features that includes fire alarm disconnect, overvoltage protection, and low power disconnect which prevents deep discharge of stand-by batteries.

Altronix eFlow104NV is a power supply/charger that converts a 220VAC (working range 198VAC - 256VAC), 50/60Hz input into a single 24VDC output with a total of 10A max. The unit includes an unswitched aux. output. It also offers a suite of features that includes fire alarm disconnect, overvoltage protection, and low power disconnect which prevents deep discharge of stand-by batteries.

Altronix eFlow104NK1 is a dual output power supply/charger kit converts a 120VAC, 60Hz input into one (1) 5VDC or 12VDC selectable output at up to 6A supply current and one (1) 24VDC output. It also offers a suite of features that includes fire alarm disconnect, overvoltage protection, and low power disconnect which prevents deep discharge of stand-by batteries.

Altronix eFlow104NK8DQP converts a 120VAC 60Hz input into eight (8) PTC protected power-limited outputs. Outputs are individually selectable, providing 12VDC or 5VDC up to 6A and/or 24VDC up to 10A (240W total power) for access control panels, door locks, and ancillary devices. Unit includes an unswitched aux. output. It also offers a suite of features that includes fire alarm disconnect, over voltage protection, and low power disconnect which prevents deep discharge of stand-by batteries. Networkable power distribution module facilitates monitoring, reporting, and control of the supervised DC power supply/charger over the network. It reports diagnostics via Email and Windows Dashboard Alert notifications, greatly reducing system downtime and eliminating unnecessary service calls.

2 Amp output, hinged box.

Bosch VGA-SBOX-COVER is a cover for AUTODOME power supply box.

3 Amp output, hinged box.

1 Amp output, hinged box.

2 Amp output, hinged box.

3 Amp output, hinged box.

1 Amp output, hinged box.

Wall mounted.

5 Amp output, hinged box.

24vAC, 1 Amp output, suits internal Spectradomes.

A full range of MIC Series power supply units (PSUs), with integrated Bosch IP technology provides all connections for power, telemetry and video for MIC Series MIC550, MIC550IR, and MIC612 cameras. The MIC IP PSU uses Dual Streaming to generate two independent IP video streams per channel if sufficient computational power is available. The MIC IP PSU features a highly flexible recording scheduler, providing up to ten programmable recording profiles and allowing individually assigned camera profiles.

2 Amp output, hinged box.

24vAC, 4 Amp output, suits internal Spectradomes.

ComNet has introduced a solar-power product line to provide operating power for remote applications where local power is not available. The NetWave Solar off the grid power systems are designed for applications where a remote camera or wireless repeater is needed but power is not available or the cost to run power is too expensive. NetWave Solar is a complete system for providing remote power to edge communications equipment. The kit includes a high quality photovoltaic solar panel, outdoor enclosure, power controller with integrated power injection module, all the mounting hardware and is available with or without sealed lead acid batteries.

The NetWave Solar off the grid power systems are designed for applications where a remote camera or wireless repeater is needed but power is not available or the cost to run power is too expensive. NetWave Solar is a complete system for providing remote power to edge communications equipment. The kit includes a high quality photovoltaic solar panel, outdoor enclosure, power controller with integrated power injection module, all the mounting hardware and is available with or without sealed lead acid batteries. The steel outdoor enclosure has a gasketed hinged lid with two tamper proof locks operated by a special key for high security.

Altronix BT126 is a rechargeable battery that supplies 12VDC/7AH for security, access, surveillance and fire applications. Features: For general purpose, up to 5 years in standby service or more than 260 cycles at 100% discharge. Sealed non-spillable lead acid batteries. Highly efficient, leak proof and maintenance free.

120 VAC power supply unit 120VAC in, 24VAC out For AUTODOME 7000, MIC IP cameras without illuminators

Bosch VG4-A-PSU0 is a 24 VAC power supply unit for PTZ camera in the AUTODOME Series. It features white aluminium enclosure with cover and is IP66 and IK8 rated.

The NetWave Solar off the grid power systems are designed for applications where a remote camera or wireless repeater is needed but power is not available or the cost to run power is too expensive. NetWave Solar is a complete system for providing remote power to edge communications equipment. The kit includes a high quality photovoltaic solar panel, outdoor enclosure, power controller with integrated power injection module, all the mounting hardware and is available with or without sealed lead acid batteries. The steel outdoor enclosure has a gasketed hinged lid with two tamper proof locks operated by a special key for high security.