CCTV Power supplies & batteries  (658)

Indoor mains power supply Output - 24 V DC, 1.5A

The UNI-PBU1 power block unit is a UL approved, outdoor rated power supply that is enclosed in a rugged, vandal resistant aluminum enclosure. It offers conversion from 220/110VAC to 24VAC (4 Amps) to power the camera, heater(s) and blower(s).

The SNCA-HPOE1 is a single-port midspan solution that provides remote Power over Ethernet (PoE) for a wide range of current and emerging high-power applications. It can reliably deliver up to 30W of power over CAT5 cabling for devices including 802.11n wireless access points, pan-tilt-zoom (PTZ) networked video security cameras and videophones. The SNCA-HPOE1 is standards compliant with IEEE 802.3at PoE, and is also backward-compatible with IEEE802.3af. It can provide power for 10/100Base-T network devices, as well as emerging Gigabit (1000Base-T) devices.

An indoor power supply with one 4 Amp 24V AC fused output.

The SNCA-POE1 is a power supply for network fixed and minidome cameras. It offers cost-effective power distribution for IP cameras, and other devices supporting IEEE802.3af PoE standard.

The SNCA-POE12, incorporating MicrosemiPowerDsine technology, offers a cost effective, fully IEEE 802.3af compliant solution to upgrade existing IP infrastructures with Power over Ehternet (PoE). The unit provides a maximum of 15.4 watts of power through each of 12 ports, ensuring safe operation of any IEEE standard IP camera over standard Ethernet cables, leaving network infrastructure completely unaltered.

Pelco POE8ATN-EU is an 8-port Power over Ethernet midspan that is designed to meet the demanding data rate and power requirements of IP cameras with high-quality streaming video capabilities. Pelco POE8ATN-EUmeets the IEEE802.3at standard for detection, connection, disconnection, and fault protection. Additionally, it is compatible with 10/100/1000Base-T systems.

The Sony SNCA-POE6, with MicrosemiPowerDsine technology, offers a cost effective, fully IEEE 802.3af compliant solution to upgrade existing IP infrastructures with Power over Ehternet (PoE). The unit provides a maximum of 15.4 watts of power through each of 6 ports, ensuring safe operation of any IEEE standard IP camera over standard Ethernet cables, leaving network infrastructure completely unaltered.

The power supplies provide 24 VAC output for 1–4 units, depending on the model selected. To compensate for voltage losses over long wire runs, 28 VAC outputs also are available on the WCS4-20. The power supplies have a selectable input of 120 or 230 VAC.

Can be used with models: SNCA-WM20G, SNCA-WM20FC, SNCA-WM40, SNCA-WMMD1, SNCA-WMMD2.

Up to 30W of PoE Power feeding on 2-pairs Compatible with IEEE 802.3af, IEEE 802.3at Protects low power devices to receive only the power they need Automatic detection and protection of non–standard ethernet terminals Parallel slide-in design for easy installation

Ideal for powering 24V AC housings and the camera. This power supply must be used when a camera is in a housing of any type (dome or fixed)

An indoor, in line power supply with one output rated at 1 Amp, 12V DC

The FlexPower FPO150 is an offline switchmode power supply-battery charger specifically designed for the lifesafety industry capable of providing two outputs, user selectable for 12 or 24VDC. One output provides continuous output power and the second is programmable to either fail-safe or fail-secure lock operation, when the on board fire alarm interface is activated.

An indoor, in line power supply with one output rated at 1 Amp, 24V AC

TDSi 2921-0273 is a 12 V 7 Ah sealed lead acid back-up battery.

The FlexPower FPO250 is an offline switchmode power supply-battery charger specifically designed for the lifesafety industry capable of providing two outputs, user selectable for 12 or 24VDC. One output provides continuous output power and the second is programmable to either fail-safe or fail-secure lock operation, when the on board fire alarm interface is activated.

Mains power supply for AXIS Companion Recorder with DIN connector IEC-C13 mains cable is not included

The FLEXPOWER FPO150/250-E2 is a dual voltage offline power supply-battery charger housed in a large cabinet for expansion and maximum field configuration flexibility. Listed modular accessories include: power distribution, relay based lock control, egress lock control, secondary voltage and network connection. Each power supply provides two pairs of outputs, each pair user selectable for 12 or 24 VDC, the unit is configured in a painted, steel, locking enclosure with tamper switch and integral battery space. One output of a pair provides continuous output power for system use, the second is programmable for either fail-safe or fail-secure operation, activated when the fire alarm disconnect is initiated. This is agency listed for access control, fire, security, CCTV, and mass notification.

Power supply for 12 V DC Extended temperature range, -40 °C to 75 °C (-40 °F to 167 °F) Voltage: 12 V DC, max current: 2.33 A

Extended temperature specification -40 °C to 75 °C (-40 °F to 167 °F) Voltage: 90 - 264 V AC (operating), 115 - 230 V AC (nominal)

D-Link DCS-80-6 outdoor power box is suitable for use with DCS-681x high speed dome network cameras.

The FLEXPOWER FPO250/250-E4 is a dual voltage offline power supply- battery charger housed in a large cabinet for expansion and maximum field configuration flexibility. Listed modular accessories include: power distribution, relay based lock control, egress lock control, secondary voltage and network connection.

LILIN SL4024A PoE Splitter supports 40W power output.

LILIN SL1212D1 PoE Splitter supports 12W power output.

SL4012D is a PoE injector & splitter.

The FLEXPOWER FPO250-E1 is an offline switchmode power supply-battery charger specifically designed for the lifesafety industry. Capable of providing two power outputs, user selectable for 12 or 24 VDC, the unit is configured in a painted, steel, locking enclosure with tamper switch and integral battery space. One output provides continuous output power for system use, the second is programmable for either fail-safe or fail-secure operation, activated when the fire alarm disconnect is initiated. This is agency listed for access control, fire, security, CCTV, and mass notification.

The FLEXPOWER FPO250-D8E1 is an offline switchmode power supply- battery charger system specifically designed for multi-output general purpose power distribution, that may be used to provide distributed power for access, fire and the CCTV segments of the lifesafety industry. Providing for system power and multiple auxiliary power distribution outputs, the unit is user selectable for 12 or 24VDC and is configured in a painted, steel, locking enclosure with tamper switch and integral battery space. Each auxiliary output is programmable for continuous power output or switched (resettable) voltage output.

Single stable voltage type Output signal delay adjustable from 0 to 35 seconds, 2 way DC output, with overload & short circuit protection, 2 way trigger signal input (switches, pulse signal) Features: Input voltage: AC220V（Option AC110V）/50Hz  Output voltage: DC12V  Maximum current: 3A  Weight: 1.8kg Dimension: 200*160*73mm Option 12V 7AH Battery 16USD

The iSCAN150/250-16 is designed specifically to support the dual voltage requirement of 12 and 24VDC, this unit utilizes two FPO power supplies to generate 24VDC and 12VDC and supports and monitors both battery sets. The system provides sixteen activation inputs and sixteen monitored and controlled relay outputs. The managed inputs are capable of voltage or dry contact activation and the managed outputs are programmable to either of the two system voltages, fail-safe, fail-secure, fire alarm over ride, and AC loss over ride for egress lock control.

The FLEXPOWER FPO150-C8E1 is a single voltage, offline switchmode power supply-battery charger system specifically designed for the access control segment of the lifesafety industry. The unit is configured in a painted, steel, locking enclosure with tamper switch and integral battery space, and provides one power supply which can be set to 12 or 24V. Eight access controlled trigger inputs control eight relay based lock outputs, with each output programmable for fire alarm disconnect, fail-safe, fail-secure, or dry contact operation.

The FlexPower C4 modules add either 4 or 8 lock control outputs to a FlexPower power supply and are typically supplied as part of a system or purchased as an expansion piece to an existing system. Each module provides either 4 or 8 access control inputs capable of voltage or dry contact activation. Each module provides either 4 or 8 lock outputs, each one programmable for fail-safe, fail-secure, dry contact, and fire alarm over ride for egress lock control

The FLEXPOWER FPO250-E2 is an offline switchmode power supply-battery charger specifically designed for the lifesafety industry. Capable of providing two power outputs, user selectable for 12 or 24 VDC, the unit is configured in a painted, steel, locking enclosure with tamper switch and integral battery space. One output provides continuous output power for system use, the second is programmable for either fail-safe or fail-secure operation, activated when the fire alarm disconnect is initiated. This is agency listed for access control, fire, security, CCTV, and mass notification.

The FLEXPOWER FPO250/250-C8D8E2 is a dual voltage, offline switchmode power supply-battery charger system specifically designed for the access control segment of the lifesafety industry. The unit is configured in a painted, steel, locking enclosure with tamper switch and integral battery space, and provides two power supplies, each of which can be set to 12 or 24V. Eight auxiliary outputs are provided for readers, REX devices, or other similar units with each output selectable for either power supply.

The FLEXPOWER FPO75-E1 is an offline switchmode power supply-bat - tery charger specifically designed for the lifesafety industry. Capable of providing two power outputs, user selectable for 12 or 24 VDC, the unit is configured in a painted, steel, locking enclosure with tamper switch and integral battery space. One output provides continuous output power for system use, the second is programmable for either fail-safe or fail-secure operation, activated when the fire alarm disconnect is initiated. This is agency listed for access control, fire, security, CCTV, and mass notification.

robust design assures extremely high reliability in unconditioned roadside environments user-selectable local, master or bus operation and DTE or DCE Interface Ensured Ease of installation and maximum versatility supports equest to Send (RTS) and Clear to Send (CTS) Signals RJ-45 expansion port provides network branching capability by electrically linking colocated transceiver units

frequency modulation for high quality video transmission directly compatible with All NTSC, PAL, or SECAM CCTV camera systems LED status indicators provide rapid indication of critical operating parameters integrated WDM for greater reliability solid-state current limiters on all power lines provide equipment protection

The DC and AC outputs connect directly to the device it is powering with wires connected to its screw terminals. 12VDC - 1.9A continuous current - Switch mode design - Mains lead.

OUTSOURCE is a compact POE injector. It injects industry-standard IEEE 802.3af POE onto Cat 5 or similar network cabling to deliver reliable remote power to IP cameras, wireless access points (WAPs) and other devices. OUTSOURCE can also deliver enhanced POE to OUTREACH Max for increased range extension and POE power. By simply routing a single network connection through OUTSOURCE it will automatically inject electrical power onto the cable whenever it detects a compatible device. OUTSOURCE is a compact, wall-mountable unit with a sealed, fanless design for reliability. Safety is assured as overload protection is incorporated and PoE will only be enabled to compliant equipment. OUTSOURCE supports Gigabit Ethernet as well as 100BASE-T and 10BASE-T. In addition to IEEE 802.3af POE, it can also deliver power to Veracity's OUTREACH Max network extender, enabling extension of POE Ethernet connections to higher-power devices over longer distances.

AXIS T8005 power supply for AXIS M10/M30 cameras with micro USB connector type B