CCTV Power supplies & batteries  (658)

The D8 power distribution module adds 8 auxiliary power outputs to a FlexPower power supply and is typically supplied as part of a system, or purchased as an expansion piece to an existing system. The D8 provides 8 auxiliary power outputs. Each output is programmable to either of the two voltages available when used in a FlexPower dual voltage power system, or to the continuous output or the resettable output of the power supply when used in a single voltage system.

Veracity's OUTBREAK is a POE splitter for 12V IP cameras and other devices, letting you upgrade network equipment to be fully POE compatible. Simply connect OUTBREAK in line with the IP camera's network connection and wire its DC output to the camera's power input. The camera can then connect to the network whilst OUTBREAK converts POE to the lower-voltage supply it requires. Available in both 5V and 12V versions.

The B100 secondary voltage module provides a means to easily and economically add an additional voltage to any FlexPower system. Primary power for the B100 is derived from an FPO power supply and the B100 steps the FPO voltage down to the user defined range (typically 12VDC*). The B100 terminal block output is Class 2 power limited and jumper selectable for either a fixed 12VDC or an adjustable range between 5-18VDC at 4 amps maximum current.

Veracity's OUTBREAK is a POE splitter for IP cameras and other devices, letting you upgrade network equipment to be fully POE compatible. Simply connect OUTBREAK in line with the IP camera's network connection and wire its DC output to the camera's power input. The camera can then connect to the network whilst OUTBREAK converts POE to the lower-voltage supply it requires. Available in both 5V and 12V versions.

110 to 240 V AC, 60/50 Hz input 13.5 V DC output at 6 amps (Power Factor 48) Supplied with 515R1 Card Cage Rack Can be provided as redundant supply with automatic switchover Fiber fail and power fail alarms Front panel indicator and MUTE switch Dry contact or 14 V DC alarm output

AMG 0.3 AMP 15vDC power supply with jackplug

24 V AC, 1.5 A, Power Supplies & Batteries

VT-PS12DC-8 from eneo has a plastic housing with 1.8m secondary cable with DC plug.

Altronix CAB4 is a power supply/battery enclosure that can accommodate a wide variety of Altronix power supplies, sub-assemblies, and accessories. Altronix enclosures feature ample knockouts that are suitable for 3/4” and 1” conduits. Features 19 Gauge grey enclosure with ample knockouts for convenient access. Wall mount enclosure for indoor use. Dimensions 7"W x 5.62"H x 4.5"D (178 mm W x 143 mm H x 114 mm D). 1/2" and 3/4" combination knockouts.

Altronix DP4 Power Distribution Module conveniently converts a single AC/DC input into four (4) individual fuse protected outputs. 

Enables M25 (3/4") conduit installation Easy to use and install Compatible with 3000i outdoor camera

Bosch MIC-SCA-S is a plain finish, stainless steel shallow conduit adapter for 4-inch PCD base. It is used as required with other mounting brackets. It has a single 25 mm side entry conduit fitting hole.

One ST3 Snap Track and two (2) DIN Rail mounting clips. Product Weight: 0.1 Lbs. (0.045 kg). Shipping Weight: 0.13 Lbs. (0.058 kg).

Enables M20 conduit installation Easy to use and install Compatible with 3000i outdoor camera

Bosch MIC-DCA-S is a plain finish, stainless steel deep conduit adapter for 4-inch PCD base. It is designed to allow a weatherproof conduit to be fitted to protect the MIC composite cable.

Altronix CP2 conversion plate allows to mount up to two (2) PD4UL(CB), PD8UL(CB), ACM4(CB), MOM5, VR6, PDS8, NetWay5B or LINQ8PD(CB) subassemblies in Altronix BC400 enclosures, for system expansion. Features 18 AWG powder coated sheet metal construction. Custom made to fit Altronix enclosures and sub-assemblies. Mounting holes for BC400 placement. Mounting pems to accommodate two (2) Altronix sub-assemblies. Mounting hardware included.

Altronix DP4CB Power Distribution Module conveniently converts a single AC/DC input into four (4) individual PTC protected outputs.

Product Weight: 0.1 Lbs. (0.045 kg). Shipping Weight: 0.15 Lbs. (0.068 kg).

The FlexPower FPO75 is an offline switchmode power supply-battery charger specifically designed for the lifesafety industry capable of providing two outputs, user selectable for 12 or 24VDC. One output provides continuous output power and the second is programmable to either fail-safe or fail-secure lock operation, when the on board fire alarm interface is activated.

Input voltage: 100-240VAC Output: 12VDC/1A Secondary cable with DC plug Plastic housing

230 V AC, 12 V DC, Power Supplies & Batteries

Camera power supply for the ESH housing series

Camera Power Supply for VHM Housing Series. Mains Input: 230VAC/50Hz. Mains Connection: Terminal Block. Voltage Output: 12VDC/0.6A, Regulated. Plugable Secondary Cable with Open Ends. Connections for Thermostat, Heater and Ground.

TDSi 2921-0281 is a boxed 2 A power supply unit with back-up battery charging facility and fault LED indication. The product can be used for all access control, CCTV or general-purpose needs. The high stability and low noise characteristics of this power supply unit makes it ideal for use in all applications.

100W PSU designed for POE applications 57V DC, 1.75A output Wide voltage range input Short circuit protection Overcurrent and overvoltage protection Auto-reset on all fault conditions Compact and fanless for high reliability Wide operating temperature range

Camera Power Supply for VHM Housing Series. Mains Input: 230VAC/50Hz. Mains Connection: Terminal Block. Voltage Output: 24VAC/0.6A. Plugable Secondary Cable with Open Ends. Connections for Thermostat, Heater and Ground.

Power Supply for ED(M)C Dome Camera Series. Mains Input: 230VAC/50Hz. Mains Connection: 1.8m with 2 pin Connector. Voltage Output: 24VAC/1.0A +/-5%. Secondary: 2 pole Cable with open Ends. For Indoor use.

TDSi 2921-0282 is a boxed 3 A power supply unit with back-up battery charging facility and fault LED indication. It is an efficient, cost-effective power supply unit housed in robust painted steel enclosure. The power supply unit can be used in all access control, CCTV or general-purpose needs.

Camera Power Supply for VTL-W/D-N2 Housing Series. Mains Input: 230VAC/50Hz. Output Power: 12VDC/0.4A, Regulated. Connection: Terminal Block.

Camera power supply for VTL-W/D-N2 housing series

eneo VT-PS12DC-10 is a plugable AC/DC adapter.

Camera power supply for the ESH housing series

240W PSU designed for Hi-POE applications 56V DC, 4.48A output Wide voltage range input Short circuit protection Overcurrent and overvoltage protection Auto-reset on all fault conditions Compact and fanless for high reliability Wide operating temperature range

Connecting an IR LED illuminator 15 Watt. Interchangeable mains contact insert.

230 V AC, 24 V AC, Power Supplies & Batteries

OUTSOURCE is a compact POE injector. It injects industry-standard IEEE 802.3af POE onto Cat 5 or similar network cabling to deliver reliable remote power to IP cameras, wireless access points (WAPs) and other devices. OUTSOURCE can also deliver enhanced POE to OUTREACH Max for increased range extension and POE power. By simply routing a single network connection through OUTSOURCE it will automatically inject electrical power onto the cable whenever it detects a compatible device. OUTSOURCE is a compact, wall-mountable unit with a sealed, fanless design for reliability. Safety is assured as overload protection is incorporated and POE will only be enabled to compliant equipment. OUTSOURCE supports Gigabit Ethernet as well as 100BASE-T and 10BASE-T. In addition to IEEE 802.3af POE, it can also deliver power to Veracity's OUTREACH Max network extender, enabling extension of POE Ethernet connections to higher-power devices over longer distances.

100W PSU designed for POE applications 57V DC, 1.75A output Wide voltage range input Short circuit protection Overcurrent and overvoltage protection Auto-reset on all fault conditions Compact and fanless for high reliability Wide operating temperature range

240W PSU designed for Hi-POE applications 56V DC, 4.48A output Wide voltage range input Short circuit protection Overcurrent and overvoltage protection Auto-reset on all fault conditions Compact and fanless for high reliability Wide operating temperature range

240W PSU designed for Hi-POE applications 56V DC, 4.48A output Wide voltage range input Short circuit protection Overcurrent and overvoltage protection Auto-reset on all fault conditions Compact and fanless for high reliability Wide operating temperature range

100W PSU designed for POE applications 57V DC, 1.75A output Wide voltage range input Short circuit protection Overcurrent and overvoltage protection Auto-reset on all fault conditions Compact and fanless for high reliability Wide operating temperature range